The WR31 Series High-Capacity Carted Wheel Rake has a high frame clearance and an increased distance between the transport wheels and raking wheels, measured at 81.3 cm (32 in.) and 45.7 cm (18 in.) respectively. This clearance allows for a high volume of crop to flow through the rake, reducing crop plugging while increasing productivity.
The 152.4-cm (60-in.) diameter raking wheels of the WR31 Series have fewer revolutions per hour than a smaller raking wheel traveling at the same ground speed. This reduction in revolutions minimizes crop leaf loss, leading operators to produce higher quality hay. A larger diameter wheel will have a longer wear life, increasing the life of the raking tines.
The WR31 Series High-Capacity Carted Wheel Rake has three easy adjustment points to fine-tune windrows and gather more hay in each bale.
1. Simply change down pressure by adjusting a spring to the desired setting for accuracy on uneven terrain.
2. Adjust wheel rake width to gather higher volumes of crop by adjusting a single pin and clip.
3. Fine-tune the windrow width by utilizing the jack to adjust the pitch of the wheel rake beams to get the right size windrow for the baler. (Only available on the WR3110 and WR3112 models)
The Kwik Pik system lifts both rake arms at the same time. This system allows for immediate clearance of the rake wheels from the crop, which in turn does not affect the windrow form during headland turns. Headland turns can be made faster, increasing productivity and uptime for the operator. The windrows will maintain a rectangular shape for easy pickup with a baler.
The adjustable hitch allows for added versatility with the WR31 Series High-Capacity Carted Wheel Rake. With the wide array of tractor tire sizes and drawbar heights, hitch adjustments add more convenience for large hay operations.
The double-acting valve allows hydraulic pressure to flow both in and out, providing a 25 percent faster hydraulic cycle time.
The ability to properly lubricate moving parts, such as the wheel, extends the life of these parts, leading to increased uptime.
The center kicker wheel conversion kit improves drying time and windrow pickup for the baler by raking the hay in the center of the rake that is not turned by the rake wheels.
When ordered as a field conversion kit, it includes one wind panel with the corresponding hardware. This is used on wheel rakes when the application is short or when raking dry crops that can blow through a standard rake wheel.
Compare the specifications of up to 4 models
Dimensions | wr31-wheel-rakes Current Model |
---|---|
Transport width | 3.05 m 10.0 ft |
Transport length | 5.18 m 17 ft |
Frame clearance | 83.57 cm 32.9 in. |
Raking width | Minimum 4.57 m 15.0 ftMaximum 5.79 m 19 ft |
Windrow width | Minimum 91.44 cm 36 in.Maximum 152.4 cm 60 in. |
Transport height | 2.18 m 7.15 ft NOTE: Transport heights can vary based on unit setup. Dimensions are for reference only. |
Weight | |
Implement | 635.03 kg 1,400 lb |
Shipping | 780.18 kg 1,720 lb |
Rake wheel | |
Quantity | Eight |
Diameter | 152.4 cm 60 in. |
Hubs | Tapered bearings |
Teeth per wheel | 40 |
Teeth diameter | 7.6 mm 0.3 in. |
Wing | |
Flex up | Limited |
Flex down | Limited |
Tractor compatibility | |
Horsepower requirements | |
SCV | Type Dual-acting (DA) valveQuantity One |
Electrical requirement | |
Minimum tractor size | |
Wheels | |
Transport | Size 205/75-15Quantity Two |
Gauge | |
Safety | |
Lights | None |
Marking | SMV |
Hitch jack | Standard |
Safety chain | Standard |
Set-up time | |
Warranty | |
© COPYRIGHT 2024 LEGACY EQUIPMENT - ALL RIGHTS RESERVED| Privacy Policy | Powered By